Hobart/Magic Eye Installation: Difference between revisions
< Hobart
No edit summary |
No edit summary |
||
| Line 3: | Line 3: | ||
== Tools Required == | == Tools Required == | ||
* Drill | * Drill | ||
* 20mm Hole Saw for Metal | * 20mm Hole Saw for Metal | ||
| Line 13: | Line 12: | ||
== Parts Required == | == Parts Required == | ||
* Laser End stop kit; | * Laser End stop kit; | ||
** Switching Power Supply | ** Switching Power Supply | ||
| Line 23: | Line 21: | ||
== Time to Complete == | == Time to Complete == | ||
For first time installation of the Magic Eye, it could take about 2 hours and 30 minutes, as you familiarise yourself with the product. With help from this guide, we expect that it can be completed in about 1 hour to 1 hour and 30 minutes. | For first time installation of the Magic Eye, it could take about 2 hours and 30 minutes, as you familiarise yourself with the product. With help from this guide, we expect that it can be completed in about 1 hour to 1 hour and 30 minutes. | ||
| Line 29: | Line 26: | ||
== Installation == | == Installation == | ||
# Isolate the appliance, by either unplugging the appliance or if it is hardwired turn the rotary switch to '0' or 'off', and lock off the switch or plug with a suitable lock-out device. | # Isolate the appliance, by either unplugging the appliance or if it is hardwired turn the rotary switch to '0' or 'off', and lock off the switch or plug with a suitable lock-out device. | ||
# Remove the front panel from the appliance using a slotted screwdriver. Be sure to hold the bottom of the front panel, so that it does not to drop and damage the front. Pull the panel away, but be aware that the control panel will remain connected to the main body of the appliance. | # Remove the front panel from the appliance using a slotted screwdriver. Be sure to hold the bottom of the front panel, so that it does not to drop and damage the front. Pull the panel away, but be aware that the control panel will remain connected to the main body of the appliance. | ||
| Line 35: | Line 31: | ||
== Testing == | == Testing == | ||
If it doesn't go bang when turned on, and stops when a tray is in front of the sensor. It'll be all good. | If it doesn't go bang when turned on, and stops when a tray is in front of the sensor. It'll be all good. | ||
[[Category:Hobart]] | [[Category:Hobart]] | ||
[[Category:Warewashing]] | [[Category:Warewashing]] | ||
Revision as of 23:21, 20 April 2025
Installation of Hobart laser end stop (or Magic Eye) is an electronic interrupted cut-off device, electric laser based end stop for rack conveyor dishwashers.
Tools Required
- Drill
- 20mm Hole Saw for Metal
- 6mm HSS drill-bits
- Side Cutters
- Wire Strips
- Pozi 2 Screwdriver
- Slotted Terminal Screwdriver
Parts Required
- Laser End stop kit;
- Switching Power Supply
- Modular Timer
- Laser PNP Sensor
- Cable for PNP Sensor
- Protective Housing
- Cable
Time to Complete
For first time installation of the Magic Eye, it could take about 2 hours and 30 minutes, as you familiarise yourself with the product. With help from this guide, we expect that it can be completed in about 1 hour to 1 hour and 30 minutes.
For first time installation of the Magic Eye, it could take about 2 hours and 30 minutes, as you familiarise yourself with the product. With help from this guide, we expect that it can be completed in about 1 hour to 1 hour and 30 minutes.
Installation
- Isolate the appliance, by either unplugging the appliance or if it is hardwired turn the rotary switch to '0' or 'off', and lock off the switch or plug with a suitable lock-out device.
- Remove the front panel from the appliance using a slotted screwdriver. Be sure to hold the bottom of the front panel, so that it does not to drop and damage the front. Pull the panel away, but be aware that the control panel will remain connected to the main body of the appliance.
- Perform a Safe Isolation Test on the appliance to confirm that it is completely turned off and safe to work on.
Testing
If it doesn't go bang when turned on, and stops when a tray is in front of the sensor. It'll be all good.